The eight services this section covers
Inspection reports the condition of the chimney and sets the level. Sweeping removes creosote and the deposits the inspection measured. Leaks and flashing covers the rain paths where the chimney meets the roof. Crown work covers the masonry slab on top of the stack. Cap and damper covers the metal at the flue opening and the plate that closes it. Masonry and tuckpointing covers the joints and the brick face. Waterproofing keeps rain out of masonry that is already sound. Relining lines or replaces the flue itself, scoped from a camera scan. Each one has its own page under this one, and which of them a chimney needs is named by the inspection report.
Water is the bridge between a chimney and a ceiling stain
A chimney is the one part of a roof that is built to have a hole in it. Rain reaches the inside of a house through four common paths at the top: a crown that has cracked and no longer sheds water clear of the brick, a missing or corroded cap that leaves the flue open to the weather, flashing that has lifted or was never counter flashed into the mortar, and masonry porous enough to absorb rain and pass it through. Each of those paths is closed a different way. The homeowner sees none of them, only a brown ring on a bedroom ceiling, a damp patch on the wall beside the fireplace, or a smell after heavy rain.
Start with the inspection, before anything is quoted
A chimney that is leaking or crumbling gets an inspection before anything is quoted. The reason is that the visible fault is often the second fault. A cracked crown is easy to see from a ladder and easy to seal; the cracked flue tile underneath it is neither, and only a camera scan inside the flue finds it. That scan is part of a level 2 inspection, which is why a level 2 is the inspection most of this work is scoped from.
What a visit looks like
The level is settled before anyone arrives, because the level decides what is looked at. A level 1 covers the readily accessible parts of the chimney and the appliance connection. A level 2 adds the accessible areas of the attic, the crawl space and the basement, and adds a camera scan inside the flue. What the inspection finds goes into a written report that names what the chimney needs and in what order, and that report is yours to hand to a buyer or an adjuster. The estimate follows the report, it is free, and it is given in writing before any work begins.
The annual inspection, and the chimney nobody lights
The Chimney Safety Institute of America quotes the national standard directly: chimneys, fireplaces and vents shall be inspected at least once a year for soundness, freedom from deposits and correct clearances. The same body states that this applies even where the chimney is little used, because animals build nests in an unused flue and materials deteriorate whether or not anything is burned in the firebox. A chimney that has not been lit in five years is not exempt from the standard, and it is often the one with the most surprising camera scan.
What a level 2 is triggered by
A level 2 inspection is booked because something has happened, not because a year has gone by. The sale or transfer of a property is the trigger a buyer's attorney or a realtor asks about. The others are a chimney fire, an operating malfunction, an external event likely to have caused damage, and a change of fuel or appliance, which includes an oil to gas conversion. If any of those has happened, a level 1 is not the inspection to book.
When to call
Call when water shows up near the fireplace or on a ceiling under the chimney after rain, when there is a smell after a storm, or when brick and mortar start dropping into the yard. Call when one of the level 2 triggers has happened: a sale or transfer, a chimney fire, an operating malfunction, an external event likely to have caused damage, or a change of fuel or appliance. Call once a year in any case, and before the burning season for the sweeping, because the annual standard applies to a chimney that is barely used as much as to one that is lit every night.
Freeze and thaw is why chimneys here fail
The United States National Park Service names water as the most destructive force on historic masonry surfaces, and describes what it does next in a cold climate: the water wicks into the brick cores, and where winter freezes are prevalent the brick deteriorates from freeze thaw action. A northern New Jersey chimney takes wind driven rain from June through the fall storm season and then freezes and thaws through the winter with that water inside it. The damage becomes visible in late winter and spring, when spalled brick and crumbling mortar get noticed, and that is why waterproofing belongs to the spring calendar here and sweeping to the fall one.
Where the chimney work meets the restoration side
When a chimney has been letting water in for a season, the work at the top is half the job. The plaster, the framing and the insulation the water passed through are wet, and wet material has a limited window before drying stops being enough and mold becomes the problem. That is the same work this business does every day for a burst pipe, with the same meters and the same written log, so the chimney work and the drying are one job.
The counties this work covers
Chimney work runs across the same eight counties as the restoration work: Passaic, Essex, Hudson, Union, Bergen, Morris, Middlesex and Somerset. It is the same team and the same schedule as the water damage side, so a chimney leak and the ceiling stain underneath it are handled on one visit by one company.